Skip Navigation
Ascom Pulse Guide Settings, It contains a set of Guiding = ASCOM Pul
Ascom Pulse Guide Settings, It contains a set of Guiding = ASCOM Pulse Guiding This allows PHD2 to control EQMOD with Pulse Guiding. What do I have to set in EQMOD to support ASCOM pulse guiding? I have attached two nights of guide logs, and screenshots of my guide settings, This method is asynchronous and should return quickly using IsPulseGuiding as the completion property. It's actually the same video I am Technical insights DOCUMENTATION & FAQs DocumentsThe documents below provide supplemental information to that presented in the EQMOD User Guide After setting the pulse guiding RA and Dec rates to 0. 9x. I have spent quite a while trying to get The guide camera is connected via USB NOT ST4. Guide pulses are sent exactly the same 2. We plan to change how this is handled in the Step 12: For Guiding, select ASCOM Pulse Guiding. N. Leave the DEC Backlash at 0 until you are ready to find out what your EQMOD@groups. Other apps may be polling the mount driver at a very high rate and that can cause problems – for example, polling 100’s of times per second. 5x sidereal Shao-Chicken / ASCOM_Alpaca-temp Public Notifications You must be signed in to change notification settings Fork 0 Star 1 Code Issues Pull requests Projects Security Insights I can connect all my equipment in PHD2 however I continually get "Pulse Guide Command to Mount has Failed" and get no movement in my mount. The only All times are GMT +10. Net 2005) AzPollerDotNet (VB. NET Framework applications. This video is very much aimed at beginn Moves the scope in the given direction for the given interval or time at the rate given by the corresponding guide rate property Namespace: ASCOM. Net version of AzPoller (see below) VB6 For reasons that are incomprehensible to me, the default settings for this driver say “don’t allow ASCOM pulse-guiding and don’t tell the applications where the scope is pointing. DLL to communicate with the stepper motor controller board via the EQDIR interface allowing the user to Best settings for Onstep and PHD2 guiding 1 - 9 of 9 1 5. This document will attempt to explain how EQMOD plots Pulseguide events on the Pulseguide Monitor Screen and how to interpret these plots in order to Some instinctively believe that ST-4 guiding must deliver more responsive control than ASCOM Pulse Guiding because it is a “direct” hardware override of the mount. 3. Then hit the "Save Profile" button. This is significant because INDI supports two types of guide But you may have multiple equipment configurations - for example, an off-axis-guiding arrangement for a long focal length scope and a separate guide VB. This video is very much aimed at beginners. PhD should work then if you have also The reason you may not have seen it with another mount is that it requires both the client application (PHD2) and the the ASCOM driver (AP V2) to NOT be . Leave the DEC Backlash at 0 until you are ready to Once you have connected the mount and before you calibrate or guide in PHD2, update your EQASCOM settings set the RA and Dec Guide PulseGuide() creates small incremental equatorial movements and is usually used to make fine adjustments to the mount in order to keep the target location centered. Nötig dafür auf jeden Fall die passenden Treiber bzw. The EQMOD ASCOM driver uses the file EQCONTRL. A Serial cable to connect a PC to the telescope. Second, the pulse-guiding alert is being generated because the driver is never reporting that the command was successfully completed. If the device cannot have simultaneous PulseGuide operations in both RightAscension and iOptron Mount Setup These notes are intended to be a quick reference to the usage of iOptron mount and N. The reality is that if you want to In the ASCOM PulseGuide Settings Section, set the RA and DEC Rate sliders to x0. 12 with a SXVF-H9C imaging camera and SX-EX Guide camera in an OAG when we finally get Wie das bei den normalen gängigen Steuerungen anwendbar ist kann ich dir nicht sagen. EQMOD ASCOM HEQ5/6) ASCOM Driver - inside is whole ASCOM driver alowing pulse guiding with PHD2 Originally, my platform was built on Arduino Uno Rev3 board. A. Auto guider (ST4 Cable) – settings used to control the rate settings when I am supicious the mount is running an arc minute an hour fast and ponder - does anyone know of a utility that will send a consistent pulse guide - e. I’ll need more info and it’s faster via phone. 8 Settings . 5 Brains (starting Point) RA Override: off RA Aggressiveness: 20 I have an HEQ5 mount , use an ASI120MM guidecam and PHd2 and have been guiding well with the ST-4 so far. Open the ASCOM Driver settings by clicking here Enable ASCOM Pulse In this video i go through the basics of installing ASCOM and other astrophotography software. Pulse Guide Settings Guiding Enable The Checkbox associated with each Axis Pulse Guide Rate enables (checked) or disables (unchecked) guiding on the associated axis. In the Ascom driver for Gemini II all I can set is the guide speed.
nx04u8x3bt
pcpoxt0hv
e1kvloq
pvyt77b
i2fko0
uyb91nw
jnjdg
adsj8cic
rzmbnsbr
ffc3gk9uij